Welcome to the Changshu Ruiyang Non-woven Machinery Co., Ltd. official website!

TEL：0512-52583778

Your current location：

Non-woven shoe cover machine

Categories:FAQ
Author:
Origin:
Time of issue:2020-11-25
Views:0

(Summary description)Overview Non-woven shoe cover machine, also known as foot mask machine, is a special machine for automatic production of elastic non-woven fabrics, plastic shoe covers or foot masks. The output can reach 30 pieces per minute. This shoe cover machine is suitable for hospitals, foot baths, and saunas. , Beauty industry or dust-free industry, the whole machine is fully automated from automatic feeding to finished products without any manual operation. Functions and features 　　 1. Stitching: Use ultrasonic waves to directly sew all kinds of fabrics without needle thread, so as to achieve waterproof effect.





Non-woven shoe cover machine

Categories:FAQ
Author:
Origin:
Time of issue:2020-11-25
Views:0

Information

Overview Non-woven shoe cover machine, also known as foot mask machine, is a special machine for automatic production of elastic non-woven fabrics, plastic shoe covers or foot masks. The output can reach 30 pieces per minute. This shoe cover machine is suitable for hospitals, foot baths, and saunas. , Beauty industry or dust-free industry, the whole machine is fully automated from automatic feeding to finished products without any manual operation. Functions and features 　　 1. Stitching: Use ultrasonic waves to directly sew all kinds of fabrics without needle thread, so as to achieve waterproof effect.　　2. Lace: Use ultrasonic waves to press all kinds of leather/fabric into any pattern without burrs.　　3. Hot stamping: Hot stamping can be performed on all kinds of leather/fabrics with ultrasonic waves, with fast speed and good effect.　　4. Hemming: The hemming of all kinds of leather/fabrics can be done by ultrasonic. Features 1. Independent research and development design, product quality is guaranteed; 　　2 Using Taiwan imported piezoelectric chip, strong and stable output; frequency conversion motor control, accurate operation; 　　3. The flower wheel made of gold steel material, the welding head is wear-resistant and has a long service life 4 The flower wheel is easy to disassemble and assemble, and can be replaced with various graphics according to customer needs; eccentric adjustment, flexible, fast, and high level 5. Fast working speed, good product effect, and guaranteed quality 6. A full set of high-quality imports Component assembly, stable performance; 　　 7. Using ultrasonic and special steel wheel processing, does not damage the edge of the cloth, no burrs 8. No preheating during work, and continuous operation.

Scan the QR code to read on your phone

Previous: Process equipment flow overview

Next: Features of automatic non-woven bag making machine

Previous: Process equipment flow overview

Next: Features of automatic non-woven bag making machine

More News

Four major non-woven fabric and film composite technologies

With the maturity of the initial processing of non-woven fabrics, more and more companies are turning their attention to the deep processing of non-woven fabrics in order to maximize the added value of products and increase the profits of enterprises. In China, the application fields of hot melt coating equipment have also been continuously expanded. The medical and sanitary material production sectors are the most widely used industries of this type of equipment. The rapid development of the automobile industry in China has also stimulated the According to the demand for coating equipment, relevant data show that the domestic geotextile industry recently introduced the first hot melt production line so far. As a mature and constantly developing process, the prospect of hot melt coating technology in the deep processing industry of non-woven fabrics will get better and better. Disposable medical supplies (such as surgical gowns, surgical sheets, wet wipes, gloves, shoes, hats, etc.), industrial protective products, and personal care products are mainly non-woven composite film products. These industries have The requirements are almost the same, namely waterproofness, breathability and comfort. This article will analyze and compare several main technological characteristics of current medical and sanitary material composites: 1. Laminating: This kind of technology is the most used method in domestic enterprises. Features: simple, mature, and fast production speed ( About 100m/min). Disadvantages: Do not make products that require breathability; feel hard and have poor comfort; higher requirements for non-woven fabrics. Non-woven fabrics with low weight (below 18gsm) and low coating weight (below 15gsm) have unsatisfactory coating effect, because the unevenness of the surface of the coil makes the coating process prone to leaks. 2. Hot rolling: It is the standard process for the two-step manufacturing of SMS non-woven fabrics. Many domestic companies use this process for composite manufacturing of films and cloths. Features: ready-made equipment and technology can be used. Disadvantages: The composition of the film is PE, and the composition of the non-woven fabric is polypropylene. The different melting points of the two make the temperature of the hot roll cannot be considered at the same time; the heat capacity of the hot roll causes different production speeds at the same temperature to lead to the uniformity of the composite strength of the product Poor; the processing accuracy of the hot embossing roll is also a factor that affects the quality of the product; the hot rolling method has a higher air permeability loss rate for the air permeable film material (between 30-40%); the production speed is slow. 3. Cloth powder compounding: A method of evenly sprinkling hot melt adhesive powder on the non-woven fabric or film, and then compounding by heat. Features: The heat pressure roller uses rubber band roller and smooth roller to cause little damage to the material. Disadvantages: slow production speed and low production efficiency; even distribution of hot melt adhesive powder is the key to product quality, but the easy hygroscopicity of hot melt adhesive powder makes it difficult to spread evenly, and the amount of distribution is not good Control; the melting temperature of hot melt adhesive powder is higher, and the melting temperature of breathable film is lower. The hot melt adhesive powder cannot be completely melted during compounding, resulting in insufficient peel strength and poor surface flatness of the compound film. 4. Hot melt adhesive breathable coating compound: Features: faster production speed, low breathable loss rate of breathable film material (between 20-30%). Disadvantages: equipment investment is large (a set of 1600mm effective width hot melt adhesive breathable coating composite hot melt adhesive system costs more than 400,000 US dollars); the gluing weight is high (at an angle of 180 о, strength 3.0N/inch composite requirements For example, the amount of glue used can reach 4gsm or more); the coating head needs to be in contact with the coating material during coating, which requires high stability and flatness of the winding and unwinding equipment; the coating process exerts relatively high tension on the material However, non-woven fabrics and films are required to run under low tension, otherwise it is easy to cause stretching and deformation of the material, and the product will wrinkle after compounding, which will affect the quality of the product.

2020-11-25

Process equipment flow overview

1.2 Overview of the process equipment flow 1. Into the cotton The raw staple fiber is manually placed on the long curtain in proportion, and the long curtain is conveyed to the entrance of the mixer. 2. Cotton blending 2-1 Use photoelectric control to control the feeding amount of cotton fed by the cotton feeder; 2-2 Use photoelectricity to control the amount of cotton stored in the blender and quantify the thickness or weight before sending it to the opening machine entrance. 3. Opening 3-1 The feeding part is controlled by the photoelectric control of the cotton feeder. 3-2 The opened raw material (short fiber) is sent to the cotton feeder through the material pipeline by a fan. 4. For cotton 4-1, use a photoelectric switch to control the raw material fed from the opener. 4-2 Use the photoelectric meter on the diagonal nail curtain to control the raw material sent to the entrance of the carding machine.入量. 5. Pre-carding 5-1 Use the frequency conversion to control the input amount thickness or weight  5-2 Method: Manually fine-tune the speed of the frequency converter and send it to the netting machine. 6. Laying machine The raw material that enters the laminating machine is fed into the main carding machine by cross-folding more than 5 layers of staple fibers that have been laid out in the horizontal and vertical directions. 7. Main carding 7-1 Frequency conversion control of the flake staple fiber sent from the web-laying machine. 7-2 The raw material the staple fiber is split through the cylinder, work roll and stripping roller. 7-3 The doffer The raw material short fiber is transferred to the messy roll. 7-4 The messy roll disrupts the fiber to increase the transverse strength. 7-5 The stripping roll strips the forming web from the messy roll and sends it to the web conveying curtain. Three-layer composite   7-6 The edge trimmed by the trimming machine enters the hot rolling. The trimmed trim is sent to the cotton feeder through the air duct. 8. Hot rolling The sheet material short fiber that enters the upper and lower hot rolls of the hot rolling mill from the main combing machine is subjected to hot press forming by adjusting the temperature and pressure of the hot roll to adjust the temperature and pressure required by the process. *The temperature of the hot roller, the hot oil 235240℃, is sent to the upper and lower hot rollers by the hot oil pump from the heating oil furnace. *Heat roller pressure: compressed air provided by the air compressor passes through the pressure regulating device, the upper pressure is 1.2MPa, the lower pressure is 0.80.9MPa, and enters the pressure regulating cylinder. 9. The product from the hot rolling mill is rolled after trimming. Long rolls are wound into rolls. The maximum diameter of rolls is 800mm. 10. Finished product inspection and weighing 10-1 Sampling and testing its physical indicators according to product quality standards (10-2) Weigh each roll of product. 11. Rewinding If there is a requirement for the number of broken ends of the product from the winding machine during the winding process, rewind and mark the broken ends. 12. Packaging, warehousing, leaving the factory 12-1 Different products are packaged and labeled, 12-2 the packaged products are put into the warehouse, and 12-3 are sold and left.

2020-11-25

Non-woven shoe cover machine

2020-11-25

Features of automatic non-woven bag making machine

1. The use of ultrasonic welding eliminates the need for needle and thread, saves the trouble of frequent needle and thread changes, and does not have the broken thread joints of traditional thread stitching. It can also perform neat partial cutting and sealing of textiles. Stitching also plays a decorative role. It has strong adhesion, can achieve waterproof effect, clear embossing, more three-dimensional relief effect on the surface, fast working speed, good product effect and high-end beauty; quality is guaranteed.　　 2. Using ultrasonic and special steel wheel processing, the edge of the seal will not crack, will not damage the edge of the cloth, and there will be no burrs or curling.　　3. No preheating is required during manufacturing, and continuous operation is possible.　　4. It is easy to operate, not much different from traditional sewing machine operation method, ordinary sewing workers can operate it. 5. Low cost, 5 to 6 times faster than traditional machines, and high efficiency. 6. The weight is about 2 tons. 　　 7. This machine can make vest bags, handbags, flat pockets, gusset bags, gusset bags, stable and efficient. 8. Five sets of ultrasonic systems 9. T-shirt bag: length 50-60cm can be set to a maximum length of 80cm, flat bag: 30 cm wide and 70-80 pcs/min; 50 cm wide and 50-60 pcs/min, generally 70g Non-woven fabric to make bags.

2020-11-25

友情链接

Time of issue:2020-11-24 16:36:22

Ruiyang Nonwoven

HOME　　　　丨　　　　ABOUT　　　　丨　　　　PRODUCTS　　　　丨　　　　PARTNER　　　　丨　　　　NEWS　　　　丨　　　　JOB　　　　丨　　　　CONTACT

Service Hotline：0512-52583778

Contact: Zhang Phone：13301571378
Address: Jiangsu Province, Changshu City branch Town Ren Yang Ying Yang Road
Copyright ©Changshu Ruiyang Non-woven Machinery Co., Ltd. www.300.cn 苏ICP备12008912号

Public account

View mobile

TEL

TEL:0512-52583778

WeChat

Sweep the add

TOP